Datalogic-scanning C-BOX 200 Manual de usuario

www.automation.datalogic.comC-BOX 200Installation Manual

C-BOX 200 2 2 INSTALLATION 2.1 PACKAGE CONTENTS Verify that the C-BOX 200 and all the parts supplied with the equipment are present and intact whe

INSTALLATION 2 2.2 OPENING THE DEVICE To install the C-BOX 200 or during normal maintenance, it is necessary to open it by unscrewing the four cover

C-BOX 200 2 2.3 MECHANICAL INSTALLATION The diagram below gives the overall dimensions of the C-BOX 200 and may be used for its installation. mmi

INSTALLATION 2 C-BOX 200 can be installed to operate in different positions. The two screw holes inside the housing of the C-BOX 200 are for mechanica

C-BOX 200 2 2.4 ELECTRICAL CONNECTIONS AND HARDWARE SETUP The following figure shows the typical layout. C-BOX 200RS232 21 Scanner PWR supplyLapto

INSTALLATION 2 The following figure shows a multidrop layout with C-BOX 200 devices connected to a Multiplexer: MULTIPLEXERC-BOX 200# 0C-BOX 200# 1C-

C-BOX 200 2 2.4.1 System Wiring The connection and wiring procedure for C-BOX 200 is described as follows: 1) Open the C-BOX 200 as described in p

INSTALLATION 2 The C-BOX 200 spring clamp connector pinouts are indicated in the following table. Refer to the scanner Installation Manual for detail

C-BOX 200 2 2.4.2 Power Supply Power is supplied to the C-BOX 200 through the pins provided on the spring clamp connector. The power switch (see Fi

INSTALLATION 2 2.4.3 Scanner Chassis Grounding Jumper Settings The scanner chassis grounding method can be selected by positioning a jumper (see Fig

Datalogic Automation S.r.l. Via S. Vitalino 13 40012 - Lippo di Calderara di Reno Bologna - Italy C-BOX 200 Ed.: 07/2007

C-BOX 200 2 2.4.5 RS485 Bus Termination ON OFF Figure 12 - Termination Resistance Switch This switch enables or disables the insertion of the

INSTALLATION 2 They are used together and they have the following significance: when a jumper is in the J1 position (see Figure above) pin 40 is conn

C-BOX 200 2 2.6 SCANNER REQUIREMENTS 1) The C-BOX 200 can be connected to the following scanners through the 25-pin connector illustrated in Figure

INSTALLATION 2 2.7.1 GET/SEND Buttons The C-BOX 200 has two internal function buttons (GET, SEND). C-BOX 200 GET SEND Figure 15 – Internal Functio

C-BOX 200 2 2.7.2 LED Indicators Power onWarningTx Figure 16 - LED Indicators The internal LEDs of the C-BOX 200 (see Figure above) indicate the

INSTALLATION 2 2.8 SCANNER REPLACEMENT If you have to replace the scanner with another one: 1. Switch-off the system. 2. Connect the new scanner. 3

C-BOX 200 3 3 TECHNICAL FEATURES ELECTRICAL FEATURES Power Supply voltage 10 to 30 Vdc Power consumption max. 1.4 W + scanner USER INTERFACE

DECLARATION OF CONFORMITY 07 Datalogic Automation S.r.l., Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that

www.automation.datalogic.comC-BOX 200Installation Manual

CONTENTS SAFETY PRECAUTIONS... iv Power Supply...

SAFETY PRECAUTIONS POWER SUPPLY ATTENTION: READ THIS INFORMATION BEFORE INSTALLING THE PRODUCT - This product is intended to be installed by Qua

ITALIANO Informazione degli utenti ai sensi della Direttiva Europea 2002/96/EC L’apparecchiatura che riporta il simbolo del bidone barrato deve esse

GENERAL VIEW C-BOX 200 23 1 Figure A 25-pin scanner connectorCover screws (4) Compression connectors1 2 3 vi

C-BOX 200 410126789125311 Figure B Power switch (ON/OFF)12Spring clamp terminal blocks3Multidrop address switches54Power on LEDWarning LED6Tx LED

GUIDE TO INSTALLATION The following can be used as a checklist to verify all of the steps necessary for complete installation of the C-BOX 200. 1)

INTRODUCTION 1 1 INTRODUCTION 1.1 PRODUCT DESCRIPTION The C-BOX 200 is a connection box which can be used as an accessory to several Datalogic fami