Datalogic Scanning POWERSCAN PD7100 Manual de usuario Pagina 121
- Pagina / 324
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Character Conversion
Product Reference Guide 113
conversion: BB22BB22.
The A characters were converted to B characters and the 1 characters were converted to
2 characters. Nothing is done with the last two character pairs, since they are all FF.
To set Character Conversion:
1. Scan the ENTER/EXIT barcode.
2. Scan the “Configure Character Conversion” barcode.
3. Determine the desired string. Sixteen positions must be determined as in the above
example. Next, turn to the ASCII Chart on the inside back cover of this manual
and find the equivalent hex digits needed to fulfill the string.
4. Turn to Appendix E, Keypad and scan the barcodes representing the hex charac-
ters determined in the previous step.
5. Scan the ENTER/EXIT barcode to exit Programming Mode.
NOTE
If less than the expected string of 16 characters are selected, scan
the ENTER/EXIT barcode twice to accept the selections and exit Pro-
gramming Mode.
- PowerScan 1
- PD7100 Corded 1
- Table of Contents 3
- 2PowerScan 4
- Product Reference Guide 5
- 6PowerScan 8
- Chapter 1 9
- Introduction 9
- Manual Conventions 10
- References 10
- Technical Support 11
- 4PowerScan 12
- Chapter 2 13
- Getting Started 13
- Setting Up the Reader 14
- Programming 15
- Select the Interface Type 16
- Configure Interface Settings 16
- Configure Other Features 16
- 9 17
- 10 PowerScan 18
- Chapter 3 19
- Interfaces 19
- 12 PowerScan 20
- 13 21
- 14 PowerScan 22
- Global Interface Features 23
- USB Suspend Mode 24
- Chapter 4 25
- General Features 25
- 18 PowerScan 26
- Label Gone Timeout 27
- Label Gone Timeout — cont 28
- Sleep Mode Timeout 29
- 22 PowerScan 30
- LED and Beeper Indicators 31
- Good Read: When to Indicate 32
- Good Read Beep Type 33
- Good Read Beep Frequency 34
- Good Read Beep Length 34
- 27 35
- Good Read Beep Volume 36
- Good Read LED Duration 37
- 30 PowerScan 38
- 2 seconds 38
- Scanning Features 39
- Scan Mode — continued 40
- Stand Mode Triggered Timeout 41
- 34 PowerScan 42
- Scanning Active Time 43
- Scanning Active Time — cont 44
- Flash On Time 45
- Flash On Time — cont 46
- Flash Off Time 47
- Flash Off Time — cont 48
- Stand Mode Sensitivity 49
- Laser Pointer Control 50
- Laser Pointer Period 51
- Laser Pointer Period — cont 52
- Green Spot Duration 53
- 46 PowerScan 54
- Chapter 5 55
- RS-232 ONLY Interface 55
- Baud Rate — continued 56
- Data Bits 57
- Stop Bits 58
- Parity = None 59
- Parity = Even 59
- Parity = Odd 59
- Handshaking Control 60
- Chapter 6 61
- RS-232/USB-Com Interfaces 61
- Intercharacter Delay 62
- Intercharacter Delay — cont 63
- Beep On ASCII BEL 64
- Beep On Not on File 64
- ACK NAK Options 65
- ACK Character 66
- ACK Character — cont 67
- NAK Character 68
- NAK Character — cont 69
- ACK NAK Timeout Value 70
- ACK NAK Timeout Value — cont 71
- ACK NAK Retry Count 72
- ACK NAK Retry Count — cont 73
- ACK NAK Error Handling 74
- Indicate Transmission Failure 75
- Disable Character 76
- Disable Character — cont 77
- Enable Character 78
- Enable Character — cont 79
- 72 PowerScan 80
- Chapter 7 81
- Keyboard Interface 81
- Country Mode 82
- Country Mode — continued 83
- Caps Lock State 85
- Send Control Characters 86
- Wedge Quiet Interval 87
- Wedge Quiet Interval — cont 88
- Intercode Delay 91
- Intercode Delay — cont 92
- USB Keyboard Speed 93
- 86 PowerScan 94
- Chapter 8 95
- USB-OEM Interface 95
- USB-OEM Device Usage 96
- Chapter 9 97
- IBM 46XX Interface 97
- 46xx Number of Host Resets 98
- 91 99
- 92 PowerScan 100
- PD7100 Corded 100
- IBM Standard Format — 101
- Code 39 Format — 101
- ENTER/EXIT PROGRAMMING MODE 101
- 94 PowerScan 102
- Chapter 10 103
- Data Editing 103
- 00 - 20 Characters (ASCII) 104
- Appendix E, Key 105
- Global AIM ID 106
- Global AIM ID — continued 107
- GS1-128 AIM ID 108
- Label ID 109
- 102 PowerScan 110
- Label ID — continued 112
- Case Conversion 120
- Character Conversion 120
- 114 PowerScan 122
- Chapter 11 123
- Symbologies 123
- UPC-A Enable/Disable 124
- UPC-A — cont 125
- UPC-E Enable/Disable 127
- UPC-E — cont 128
- GTIN Formatting 131
- EAN 13 Enable/Disable 132
- EAN 13 — cont 133
- EAN-13 ISBN Conversion 134
- EAN 8 Enable/Disable 136
- EAN 8 — cont 137
- UPC/EAN Global Settings 139
- 132 PowerScan 140
- UPC/EAN Correlation 141
- UPC/EAN Reconstruction 141
- UPC/EAN Price Weight Check 142
- UPC-A Minimum Reads 143
- Optional Add-ons 144
- Add-Ons — cont 145
- GS1 DataBar Omnidirectional 155
- 148 PowerScan 156
- GS1 DataBar Expanded 157
- GS1 DataBar Expanded — cont 158
- GS1 DataBar Limited 164
- GS1 DataBar Limited — cont 165
- Code 39 Enable/Disable 166
- Code 39 — cont 167
- Code 39 Stitching 182
- Code 32 Enable/Disable 183
- Code 32 — cont 184
- Code 128 185
- Code 128 — cont 186
- GS1-128 Enable 199
- Interleaved 2 of 5 (I 2 of 5) 200
- 193 201
- 194 PowerScan 202
- I 2 of 5 Minimum Reads 203
- 2 of 5 Decoding Level 204
- 2 of 5 Decoding Level — cont 205
- I 2 of 5 Length Control 206
- I 2 of 5 Set Length 1 207
- 200 PowerScan 208
- 06 = Length 1 is 6 Characters 208
- I 2 of 5 Set Length 2 209
- I 2 of 5 Set Length 2 — cont 210
- 203 211
- I 2 of 5 Stitching 212
- Datalogic 2 of 5 213
- Datalogic 2 of 5 — cont 214
- 214 PowerScan 222
- Codabar Enable/Disable 225
- Codabar — cont 226
- Codabar Stitching 242
- Code 11 Enable/Disable 243
- Code 11 — cont 244
- Code 11 Decoding Level 254
- Code 11 Stitching 257
- Standard 2 of 5 258
- Standard 2 of 5 — cont 259
- Standard 2 of 5 Stitching 267
- ISBT 128 268
- ISBT 128 — cont 269
- Code 4 Enable/Disable 270
- Code 4 — cont 271
- Code 5 Enable/Disable 272
- Code 5 — cont 273
- Code 4 and 5 Decoding Level 274
- 267 275
- 268 PowerScan 276
- Follett 2 of 5 277
- 270 PowerScan 278
- Appendix A 279
- 272 PowerScan 280
- Standard Cable Pinouts 281
- 274 PowerScan 282
- Appendix B 283
- 276 PowerScan 284
- 277 285
- 279 287
- 280 PowerScan 288
- Interleaved 2 of 5 288
- 281 289
- 282 PowerScan 290
- 283 291
- Default Exceptions 292
- 285 293
- Interface: RS232-OPOS 293
- 286 PowerScan 294
- Appendix C 295
- LED and Beeper Indications 296
- NUMBER OF LED 297
- FLASHES/BEEPS 297
- ERROR CORRECTIVE ACTION 297
- 290 PowerScan 298
- Appendix D 299
- Sample Barcodes — continued 300
- Code 32 300
- Codabar 300
- Code 93 300
- Code 11 300
- GS1 DataBar (RSS) 301
- 294 PowerScan 302
- Appendix E 303
- 296 PowerScan 304
- 297 305
- 298 PowerScan 306
- Appendix F 307
- Product Reference Guide 300 308
- Product Reference Guide 301 309
- Product Reference Guide 302 310
- Product Reference Guide 303 311
- Digital Interface 312
- Digital Interface — cont 313
- IBM31xx 102-key 314
- IBM31xx 102-key — cont 315
- IBM XT — cont 317
- 310 PowerScan 318
- 311 319
- 312 PowerScan 320
- ASCII Chart 323
Relacionado con productos y manuales para Lectores De Códigos De Barras Datalogic Scanning POWERSCAN PD7100
(200 paginas)
(65 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales